Revisiting an old project

This blog post is about the Onion Ring Magic Square. You can get to the free pattern by clicking HERE.

It's been a long time since I've worked on this piece of tatting. The last time I blogged about it was just about two years ago. I had originally planned to make the square bigger, but I changed my mind for two reasons. Firstly, I don't want to get overwhelmed by the amount of tatting and have this piece end up in the drawer again. Secondly, I'd like to try adding the border that I designed earlier this year, and I would not be able to do that with the original plans for the square. Here's my progress so far:

I had to undo a few rings and chains so that I could change direction from my original plan. Luckily, the process went smoothly and I didn't have any thread breakage.

I'm so glad I have information stored on my blog. I had forgotten what thread I was using for this project and had to look at my previous blog posts to find out. It's Lizbeth size 40 in Ocean Teal Medium, and DMC Cordonnet Special size 40 in Blanc (white):

I'm hoping to have the square finished within the next week or two and then I will be able to start on the border.

Trefoil Table Runner

After a year and a half, and about 200 hours of tatting, the trefoil table runner is finally finished:

The runner is tatted in Lizbeth size 20 thread. It measures 55 inches long and 8.5 inches wide. It is all tatted in one pass. You can get to the Etsy listing for the pattern by clicking HERE

I want to use this blog post as a companion to the written pattern (there's a link within the pattern that will direct here). I will be showing in progress photos of the table runner and will include some additional information at the bottom of the post.

The Trefoil Table Runner began as a challenge to make a magic rectangle (a rectangle that could be expanded to any size, all in one pass). I soon realized that the tatting path for this rectangle would be much different than what I was used to for magic squares. Instead of the complex magic square path, I needed to work back and forth in rows, similar to making a crochet blanket. However, to make both sides symmetrical, I had to work one half at a time. The tatting path is shown below:

For the actual runner, I started by making a strip of connected trefoils. I worked to half of the length of the dining table, letting the end of the runner drape a bit before turning the corner. Our table has a line down the middle where two pieces connect, so it was easy to measure the halfway point:

After turning the corner, I worked my way back to the middle of the table. Upon reaching the middle of the table I made another turn:

I want to point out that there is an extra trefoil along the edge. Below is a closer photo of it. The extra trefoil will line up with the middle part of the runner:

I continued working in this zig-zag fashion. Here is the second column in progress:

I decided to work a tapered edge to give the pattern a little more visual interest. Here are the third, fourth, and fifth columns being tatted:

After finishing the fifth column, my table runner was at the halfway point. I then needed to create a mirror image of the first half of the runner. Without cutting my thread, I worked another strip of trefoils, making sure it was the same length as the first half. At this point, I needed to move my table runner to the ottoman because it was becoming too long to photograph:

As with the first half of the runner, I worked back and forth in a zig-zag path. The two halves are connected horizontally, through the middle of the runner. Below is the seventh column being built and connected back to the first half of the runner:

The eighth and ninth columns are made in the same way. The tapered edge mirrors what was done for the first half of the runner:

The tenth and final column is worked back to the starting point. The last elements are joined back to the first, and the thread is cut, tied, and sewn in:

Here is a closer photo of the runner, including the tapered edge:

I worked from a 1 kg cone of Lizbeth size 20 thread. My finished runner weighs 107 grams, which is equivalent to about 5 balls of Lizbeth thread (each ball weighing 25 grams):

In total, my table runner has 478 trefoils. Each trefoil took about 25 minutes to tat (only 20 minutes for trefoils along the edge because they didn't have thrown rings). Using several Catherine wheel joins definitely slowed my tatting down quite a bit. Adjustments can be made to use other join types if speed is of concern.

3 in 1 Hexagon

Working on the table runner can be monotonous, so I spent some time putting together a different pattern. It's a hexagon that can be connected together to form a mat, or embellished to make snowflakes:

The pattern is available in my Etsy shop and you can get to the listing by clicking HERE.

The snowflakes have interchangeable centers, pictured below:

I couldn't help but wonder what the mat would look like if it was enlarged, so I used an app on my iPad called Photo Grid to splice together some images. The first is a hexagon shaped mat:

The next is an extended mat, which could be used as a table runner:

The thread is Lizbeth size 20 in White (#601) and Cotton Candy (#111). I think the extended mat would look nice if the motifs around the edge were changed to all white.

400 Trefoils

I'm getting closer to finishing the table runner. It's up to 400 trefoils now (78 more left to finish the runner):

Here is another angle on the table:

And on the ottoman to see the full runner:

Right now, I'm working on another project, but I still plan to finish the runner before the end of the year. The pattern has been written up and I have tested some parts of it already.

350 Trefoils

I'm slowly making progress on my table runner. It's up to 350 trefoils now:

I will continue to post updates periodically, as I make my way through the rest of the runner. I still have to write up the pattern for this and am hoping to have it in my Etsy shop sometime later this year.